DESAIN RANCANGAN SIMULASI UNIPOLAR INVERTER ON GRID DENGAN METODE KONTROL ARUS MENGGUNAKAN PSIM SOFTWARE | ELECTRONIC THESES AND DISSERTATION

Electronic Theses and Dissertation

Universitas Syiah Kuala

    SKRIPSI

DESAIN RANCANGAN SIMULASI UNIPOLAR INVERTER ON GRID DENGAN METODE KONTROL ARUS MENGGUNAKAN PSIM SOFTWARE


Pengarang

Katrin Nada - Personal Name;

Dosen Pembimbing

Suriadi - 197206061998021001 - Dosen Pembimbing I
Ir. Ramdhan Halid Siregar, S.T., M.T., IPM. - - - Dosen Pembimbing II
Mahdi Syukri - 196812101998021001 - Penguji
Mansur Gapy - 195810041986031001 - Penguji
Yunidar - 197406292000032001 - Penguji



Nomor Pokok Mahasiswa

1504105010031

Fakultas & Prodi

Fakultas Teknik / Teknik Elektro (S1) / PDDIKTI : 20201

Subject
-
Kata Kunci
-
Penerbit

Banda Aceh : Fakultas Teknik., 2022

Bahasa

No Classification

-

Literature Searching Service

Hard copy atau foto copy dari buku ini dapat diberikan dengan syarat ketentuan berlaku, jika berminat, silahkan hubungi via telegram (Chat Services LSS)

Penelitian ini menjelaskan tentang desain simulasi dan prinsip kerja unipolar inverter on grid dengan memakai metode kontrol arus menggunakan perangkat lunak PSIM. Rangkaian inverter yang dipakai merupakan rangkaian inverter jembatan penuh menggunakan sistem kendali dengan metode kontrol arus. Rangkaian filter yang dipakai merupakan filter low pass (LC) menggunakan nilai L sebesar 4.06 mH dan nilai C sebesar 6.23 ɥF. Rangkaian kendali yang dipakai merupakan rangkaian SPWM (Sinusoidal Pulse Width Modulation). Daya yang disuplai oleh inverter ke grid dipengaruhi oleh besar sudut phasa, tegangan, dan frekuensi sama. Grid akan menampung kelebihan daya yang dihasilkan oleh inverter dan juga akan menyuplai daya jika inverter kekurangan daya dari sumber PLTS. Penelitian ini juga bertujuan mengatur daya pada beban agar daya yang disuplai ke beban optimal, dengan suplai utama berasal dari inverter dan kekurangan suplai daya dapat diperbantukan oleh PLN. Hal ini di tunjukkan ketika di atur arus referensi sebesar 4 A, maka diperoleh arus yang dibutuhkan beban sebesar 5,65 A, yang mana inverter hanya menyuplai arus ke beban sebesar 3,44 A, dan kekurangannya di suplai dari grid sebesar 2,207 A. Nilai frekuensi pada sistem konstan dengan nilai 50Hz. Metode current control bertujuan agar arus yang disuplai ke beban diperoleh dengan mengatur skala prioritas suplai arus, dimana arus inverter sebagai sumber arus utama dan sumber arus PLN sebagai suplai sekunder.
Kata kunci: Inverter, PLTS, On Grid, PSIM

Abstract- This research describes the simulation design and working principle of unipolar inverter on grid by using current control method using PSIM software. The inverter circuit used is a full bridge inverter circuit using a control system with a current control method. The filter circuit used is a low pass (LC) filter using an L value of 4.06 mH and a C value of 6.23 F. The control circuit used is a SPWM (Sinusoidal Pulse Width Modulation) circuit. The power supplied by the inverter to the grid is affected by the same phase angle, voltage and frequency. The grid will accommodate the excess power generated by the inverter and will also supply power if the inverter lacks power from the PLTS source. This study also aims to regulate the power at the load so that the power supplied to the load is optimal, with the main supply coming from the inverter and the lack of power supply can be assisted by PLN. This is shown when the reference current is set to 4 A, then the required power of the load is 5.65 A, where the inverter supplies power to the load of 3.44 A, and the shortage is supplied from the grid by 2.207 A. The frequency value on a constant system with a value of 50Hz. The current control method aims to ensure that the current supplied to the load is obtained by setting the current supply priority scale, where the inverter current is the main current source and the PLN current source is the secondary supply. Keywords: Inverter, PLTS, On Grid, PSIM

Citation



    SERVICES DESK